background image

 

60 

 

Wireless  Separation

:  Wireless  separation  is  an  ideal  way  to  enhance  the  security  of  network 

transmission. Under the mode except  wireless client  mode, enable “

Wireless  Separation

” can 

prevent the communication among associated wireless clients.

 

WMM Support

: WMM (Wi-Fi Multimedia) is a subset of 802.11e. It allows wireless communication 

to define a priority limit on the basis of data type under AP mode only, thus those time-sensitive 

data, like video/audio data, may own a higher priority than common one.    To enable WMM, the 

wireless client should also support it 

Max. Station Number:

 By checking the “

Max. Station Num

” the JetWave 2450v2 will only allow 

up to 32 wireless clients to associate with for better bandwidth for each client.    By disabling the 

checkbox  the  JetWave  2450v2  will  allow  up  to  128  clients  to  connect,  but  it  is  likely  to  cause 

network congestion or poor performance. 

 

Security Setting: 

To prevent unauthorized radios from accessing data transmitting over the connectivity, the IEEE 

802.11a/n JetWave 2450v2 provides you with rock solid security settings.   

 

Network Authentication 

Open System

: It allows any device to join the network without performing any security check. 

Shared Key

: Data encryption and key are required for wireless authentication (Not available in 

Bridge/AP Repeater mode). 

Legacy  802.1x

: It provides the rights to access the  wireless network and  wired  Ethernet. With 

User and PC identity, centralized authentication as well as dynamic key management, it controls 

the security risk of wireless network to the  lowest. To serve the  802.1x, at  least one  EAP  type 

should be supported by the RADIUS Server, AP and wireless client.   

WPA  with  RADIUS

:  Wi-Fi  Protected  Access  (WPA)  is  a  subset  of  the  IEEE  802.11i  standard.   

With warrant (username, password and etc.) offered by user, this kind of authentication can be 

realized with specific RADIUS server. This is the common way to be adopted in large enterprise 

network.

 

WPA2 with RADIUS

: WPA2 (IEEE 802.11i) is a wireless security standard that defines stronger 

encryption, authentication and key management than WPA.    If it is selected, AES encryption and 

RADIUS server are required.

 

WPA&WPA2 with RADIUS

: It provides options of WPA (TKIP) or WPA2 (AES) for the client. If it is 

Summary of Contents for JetWave 2450 v2















































































Reviews: