background image

Instale el montaje de ancla superior (72678M-B7, 78298M-B7)

Seleccione una ubicación en la pared para instalar la columna de la regadera de acuerdo a las dimensiones 
aproximadas.

Ensaye la instalación del kit de la barra de desplazamiento para determinar la ubicación del montaje de la ancla 
superior.

Instale el empalme del tubo en el base y aprete los tornillos con una llave hexagonal.

Desplace el empalme de tubo y el chapetón en el conector.

Atornille el empalme de tubo con la llave hexagonal y aprételos.

Ajuste manualmente la tuerca con la arandela de goma a la salida de la grifería.

Coloque la base de la grifería sobre la pared terminada. (NOTA: La 

fl

 echa en la base es hacia arriba como se muestra.) 

Marque el punto central de los tres ori

fi

 cios del con un lápiz.

A

fl

 oje la tuerca manualmente, quite la arandela de goma y remueva la barra de regadera.

A

fl

 oje los tornillos con una llave hexagonal. (NOTA: No pierda los tornillos.) Retire la base y el empalme de tubo.

Perfore tres ori

fi

 cios en el punto central como el diámetro de las anclas.

Presione un ancla en el ori

fi

 cio.

Asegure la base, mediante un tornillo.

Install the Top Base Assembly (72678M-B7, 78298M-B7)

Select a location on the wall to install the shower column according to approximate dimensions.

Dry 

fi

 t the slidebar kit to determine the anchor mounting location.

Install the tube to the base and tighten the setscrews with the hex wrench.

Slide the tube and the escutcheon onto the connector.

Thread the setscrews into the tube with the hex wrench, and tighten them.

Hand-tighten the nut with the washer onto the faucet outlet.

Place the base against the 

fi

 nished wall. (NOTE: Orient the arrow up as shown.) Mark the centerpoint of the three base 

holes with a pencil.

Loosen the nut by hand, then remove the washer and slidebar kit.

Loosen the setscrews with the hex wrench. (NOTE: Do not lose the setscrews.) Remove the base and tube.

Drill three holes at the marked locations to accommodate the anchor size.

Kohler Co.

1124467-M2-

B

4

Tornillo
Screw

Tubo
Tube

Arandela
Washer

Tuerca
Nut

Salida
Outlet

Llave hexagonal
Hex Wrench

Tornillos
Setscrews

Conector
Connector

Barra desplazamiento
Slidebar

Ancla
Anchor

Base
Base

Chapetón
Escutcheon

Summary of Contents for 72678M-7









Reviews: