background image

Instale el montaje de ancla superior (72678M-7)

Ensaye la instalación del kit de la barra de desplazamiento para determinar la ubicación del montaje de la ancla 
superior.

Desplace la base en el conector que se inserta en la base alrededor de 26 mm.

Atornille la base con la llave hexagonal y aprételos.

Ajuste manualmente la tuerca con la arandela de goma a la salida de la grifería.

Coloque la base de la grifería sobre la pared terminada.

Marque el diámetro de la base con un lápiz.

A

fl

 oje la tuerca manualmente, quite la arandela de goma y remueva la barra de regadera.

A

fl

 oje los tornillos con una llave hexagonal. (NOTA: No pierda los tornillos.) Retire la base.

Marque el punto central del diámetro de la base con un lápiz.

Perfore un ori

fi

 cio en el punto central como el diámetro de las anclas.

Presione un ancla en el ori

fi

 cio.

Asegure la base, mediante un tornillo con arandela, asegúrese que los dos ori

fi

 cios del tornillo de la base estén hacia 

debajo de forma vertical.

Install the Top Base Assembly (72678M-7)

Dry 

fi

 t the slidebar kit to determine the anchor mounting location.

Slide the base onto the connector approximately 26 mm.

Thread the setscrews into the base with the hex wrench and tighten.

Hand-tighten the nut with the washer onto the faucet outlet.

Place the base against the 

fi

 nished wall.

Trace the diameter of the base with a pencil.

Loosen the nut by hand, then remove the washer and slidebar kit.

Loosen the setscrews with the hex wrench. (NOTE: Do not lose the setscrews.) Remove the base.

Mark the centerpoint of the base diameter with a pencil.

Drill a hole on the centerpoint to accommodate the anchor size.

Press the anchor into the hole.

Secure the base with the self-tapping screw and washer, making sure the two setscrew holes are facing downwards.

1124467-M2-

B

Kohler Co.

3

Ancla
Anchor

Base
Base

Llave hexagonal
Hex Wrench

Tornillos
Setscrews

Tornillo
Screw

Conector
Connector

Barra desplazamiento
Slidebar

Punto central
Centerpoint

Ø30 mm

Arandela
Washer

Arandela
Washer

Tuerca
Nut

Salida
Outlet

Summary of Contents for 72678M-7









Reviews: