manualshive.com logo in svg

Kodak Guidelines 3000 series, User Manual, Page: 73 / 79

Share
Download
Kodak Guidelines 3000 series User Manual Download Page 73

Troubleshooting

KODAK PROFESSIONAL Large

Format 3000 Series Inkjet Printers

68

Is the Scroller installed
correctly?

Install the Scroller correctly.

Installing the Printer

Are the driver rollers clean?

Clean the driver rollers.

Maintaining the
Printer

Is the media sensor dirty?

Clean the media sensor.

Installing the Printer

Are you using the printer in
the correct environment?

Use your printer in the right
environment. (No direct
sunlight)

Setting up the Printer

12.   During the media initialization, the media wrinkles.

Possible Cause

Solution

Reference

Are you using approved
media?

Use only approved media.

Setting Up the Printer

Is the hold lever down?

Make sure to put the hold
lever in the DOWN position

Setting Up the Printer

In case of a cut sheet, is the
edge of the media aligned
with the leading edge of the
print plate?

Align the edge of the cut
sheet with the leading edge of
the print plate.

Setting Up the Printer

In case of using roll media, is
the edge of the media parallel
with the edge of the printer
during the media detection
sequence?

The roll media and the
baseline should be aligned.

Setting Up the Printer

Is the scroller installed
correctly?

Install the scroller correctly.

Installing the Printer

Is the driver roller clean?

Clean the driver roller.

Maintaining the
Printer

Is the media sensor dirty?

Clean the media sensor.

Setting Up the Printer

Are you using the printer in
the correct environment?

Use your printer in the right
environment.
(No direct sunlight)

13.   Can't run the media search in tracing paper or thin media.

Possible Cause

Solution

Reference

Are you using approved
media?

Use only approved media.

Setting Up the Printer

Are

 

you using the printer in a

wrong environment such as in
direct sunlight?

Use the printer in the
approved environment.
Remove incorrect light source
or move printer.

Installing the Printer

Summary of Contents for Guidelines 3000 series
















































































Reviews:

No comments