Kodak Guidelines 3000 series User Manual Download

Page: 67 / 79

Maintaining
the Printer

KODAK PROFESSIONAL Large

Format 3000 Series Inkjet Printers

REPLACING THE MEDIA CUTTER BLADE

Depending upon the roll media used, dust gathers in the cutter slot and on the cutter
blade edge causing irregular cuts. If necessary, replace or clean the cutting blade and
clean the cutter slot. We recommend replacing the cutting blade regularly.

1. Turn the printer OFF, and make sure that the media hold lever is in the down

position. Move the printing head to the center of the printer.

2. Push the cutter head down, rotate the cutter arm toward you, and remove the cutting

blade. Clean the cutting blade with a dry cloth, or replace it.

CAUTION:

There is a spring fitted in the hole of cutter head. Be careful not to
lose it while replacing the cutting blade.

Summary of Contents for Guidelines 3000 series
















































































Search results

Summary of Contents for Guidelines 3000 series

Reviews:

Related manuals for Guidelines 3000 series

Brands by name

Popular brands

Kodak Guidelines 3000 series, User Manual

Search results

Summary of Contents for Guidelines 3000 series

Reviews:

Related manuals for Guidelines 3000 series

Brands by name

Popular brands