Kodak Guidelines 3000 series User Manual Download | Manualshive

Page: 36 / 79

background image

Setting up the Printer

KODAK PROFESSIONAL Large

Format 3000 Series Inkjet Printers

31

2. From the back of the printer, install the ink cassettes from right to left in the correct

slots.

•

For a printer that uses four ink cassettes, install them as follows:

−

Slot 1 – Black

−

Slot 2 – Cyan

−

Slot 3 – Magenta

−

Slot 4 – Yellow

•

For a printer that uses six ink cassettes, install the additional two cassettes as

follows:

−

Slot 5 – Light cyan (orange)

−

Slot 6 – Light magenta (green)

NOTE :

Slots 1 – 4 for the black, cyan, magenta, and yellow ink cassettes
are coded so that you cannot install the cassettes in the wrong slot.
Slots 5 and 6 are not coded, so make sure that you install the light
cyan and light magenta (or orange and green) cassettes in the
correct slots.

The control panel displays the following message after the ink cassettes are installed:

USER NO MEDIA

After this message displays, automatic ink replenishment begins.

INK REFILL REST 4M

«
...
34
35
36
37
38
...
»

Summary of Contents for Guidelines 3000 series
















































































Reviews:

No comments

Related manuals for Guidelines 3000 series

Brand: Citizen Pages: 80

201021 - P 330N Photo Printer

Brand: Olympus Pages: 79

Brand: Magicard Pages: 108

Brand: SAGEMCOM Pages: 146

Brand: idp Pages: 48

Brand: Xiamen Hanin Electronic Technology Pages: 27

Brand: LaserLine Pages: 14

SpeedSetter 300

Brand: Xante Pages: 1

Brand: Olivetti Pages: 204

Brand: Triumph Adler Pages: 4

Brand: Konica Minolta Pages: 12

Brand: Olivetti Pages: 132

Brand: Xerox Pages: 78

Brand: Oki Pages: 76

All in One Printer

Brand: Epson Pages: 210

aculaser cx37 series

Brand: Epson Pages: 261

AL-MX200 Series

Brand: Epson Pages: 410

AcuLaser CX29DNF

Brand: Epson Pages: 456

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands