Kodak Guidelines 3000 series User Manual Download

Page: 58 / 79

Maintaining
the Printer

KODAK PROFESSIONAL Large

Format 3000 Series Inkjet Printers

EMPTYING THE WASTE BOX

The waste box is located at the back of the printer and collects the waste ink.

Replace the box when it is full.

1. If the control panel displays this message

when you turn the printer on, check the waste box.

2. When the front panel displays pull

out the waste box.

The message changes to:

3. Place the waste box in the plastic bag that is shipped with a new waste liquid box.

Do not tilt the waste box when you put it in the plastic bag.

4. Dispose of the plastic bag with the used waste liquid box according to regional

environmental regulations.

5. Insert a new waste box in the printer.

6. Press

either

value +

value -

key on the operation panel and the indication will change to

YES

CHECK WASTE BOX

WASTE BOX NOT FITTED

WASTE BIN FULL

CHANGE TANK? NO

CHANGED? YES

Summary of Contents for Guidelines 3000 series
















































































Search results

Summary of Contents for Guidelines 3000 series

Reviews:

Related manuals for Guidelines 3000 series

Brands by name

Popular brands

Kodak Guidelines 3000 series, User Manual

Search results

Summary of Contents for Guidelines 3000 series

Reviews:

Related manuals for Guidelines 3000 series

Brands by name

Popular brands