Knoll Antenna Telescope Installation Instructions And Parts Manual Download Page 96

Page: 96 / 115

Antenna

Telescope

™

Antenna

Telescope

™

Installation Instructions

October 2018

Telescope 120 Power Strip

Pattern Numbers Represented:

Power Strip,

YR1TPS12

Parts List:

Plug Strip (A)
Front Power Strip Clamp (B)
Rear Power Strip Clamp (C)
¼-20

" Hex Socket Flat Head Machine

Screw (D)
Knurled Collared Thumb Screw (E)
3/

" Diameter Black Nylon P-Clamp (F)

#6 x

Pan Head Wood Screw (G)

Pre-assembled Telescope 120 Table

Tools Needed:

Power Driver
Phillips #2 Bit

(A) 3AF5043

(E) 3AF4076

(B) 3AF4071

(F) 3AE5010

(G) 4A22272

(D) 3AF4077

STEPS

1. Join a front power strip clamp (B) and a

rear power strip clamp (C) around the rear
rail of the Telescope table assembly and
fasten together, using a ¼-20

" hex

socket flat head machine screw (D).

Repeat this assembly with a second
set of the same hardware, and space
the clamp assemblies approximately
8½" apart, centered on the rear rail.

2. Press the back of the plug strip (A) onto

the two clamp assemblies, with the outlets
facing the user side of the table.

3. Thread a knurled collared thumb screw (E)

into the bottom of each clamp assembly and
tighten by hand to fix the plug strip into place.

4. Use the included

" dia. black nylon

P-clamps with their corresponding #6 x

pan head wood screws (I) to manage

the power cord along the underside
of the worksurface, as necessary.

Summary of Contents for Antenna Telescope




















































































































Search results

Summary of Contents for Antenna Telescope

Reviews:

Related manuals for Antenna Telescope

Brands by name

Popular brands

Knoll Antenna Telescope, Installation Instructions And Parts Manual

Search results

Summary of Contents for Antenna Telescope

Reviews:

Related manuals for Antenna Telescope

Brands by name

Popular brands