Knoll Antenna Telescope Installation Instructions And Parts Manual Download Page 103

Page: 103 / 115

Antenna

Telescope

™

Antenna

Telescope

™

Installation Instructions

October 2018

103

STEPS

1. Determine the side-to-side location for

the hinged plate cover. The cover should
be mounted directly below the cleat
plate cable manager and power strip.

2. Attach two rail clips (A) to the back

desk rail, from behind the rail, one
on either side of the power strip.

NOTE

: If the worksurface has already been

attached, a pry bar may need to be used to
create a gap large enough to position the
clips between the worksurface and the rail.

3. Adjust the spacing of the rail clips as

necessary, and hang the cleat plate cover from
the hooks at the bottom of the rail clips (A).

4. Rotate the cleat plate cover up so that

it engages with both rails. The back
edges should engage the back rail first,
followed by the front edge of the cover,
which will engage the front rail.

NOTE

: The cleat plate cover's back tabs

may need to be bent and adjusted for
proper fit and secure connection to rails.

5. Screw a #6 x 5/8" wood screw (B) into each

rail clip (A) to secure their placement.

Telescope Hinged Cleat Plate Covers

Pattern Numbers Represented:

Hinged Cleat Plate Cover,

YR1TCPC_

Parts List:

Rail Clip (A)
#6 x

" Wood Screw (B)

Cleat Plate Cover
Pre-assembled Telescope Table with
Cleat Plate and Power Strip

Tools Needed:

Pry Bar
Phillips Screw Driver

(A) 3AF4137

Power and Cable Management

(B) 7528496

Summary of Contents for Antenna Telescope




















































































































Search results

Summary of Contents for Antenna Telescope

Reviews:

Related manuals for Antenna Telescope

Brands by name

Popular brands

Knoll Antenna Telescope, Installation Instructions And Parts Manual

Search results

Summary of Contents for Antenna Telescope

Reviews:

Related manuals for Antenna Telescope

Brands by name

Popular brands