klover DIVA SLIM, Installation, Use, Maintenance And Helpful Tips

Page: 42 / 52

DIVA SLIM AIR PELLET STOVE
40
EN - Rev. 1.0
PCB PARAMETERS
The parameters stored on the PCB are essential for the correct operation.
The following parameters are already stored during the testing of the appliance directly in the factory; these parameters
are the result of special tests using several types of pellets and must not be changed without the authorisation of Klover
srl so as not to impair the operation of the appliance.
The company shall not be held liable for any damage caused by the incorrect entry of parameters.
Parameter tables DIVA SLIM AIR
“CLEANER SETTINGS” parameters - Model DSA (L15_181119)
Parameter Menu level Description Display Measurement Value field
Database
P1
Pr51 M10 – 01 – 01 ON time for brazier cleaning gear motor CLEANING TIME Seconds 0 – 120” 13
Pr52 M10 – 01 – 02 Time from switching off after which the brazier cleaning cycle starts CLEANER DELAY Minutes 1 – 15 6
Pr53 M10 – 01 – 03 Time from switching on after which the brazier cleaning cycle starts CLEANER STAND-BY Hours 1 – 24 9
“DUCTING SETTINGS” parameters - Model DSA (L15_181119)
Parameter Menu level Description Display Measurement Value field
Database
P1
Pr55 M10 – 03 – 01 Enables ducting operation ENABLE DUCT. Off / Mode
Off
S1 – S2 – S1+2
T1 – T2 – T1+2
A1 – A2 – A1+2
Off
Pr56 M10 – 03 – 02 Allows for choosing whether the ducted air fans can be switched “OFF”. DUCTED OFF On – Off On – Off Off
Pr57 M10 – 03 – 03 Heat exchanger 2 (ducting 1) in power 1 work phase DUCT.1 SPEED-S1 Volt 65 – 225 65
Pr58 M10 – 03 – 04 Heat exchanger 2 (ducting 1) speed in power 2 work phase DUCT.1 SPEED-S2 Volt 65 – 225 65
Pr59 M10 – 03 – 05 Heat exchanger 2 (ducting 1) in power 3 work phase DUCT.1 SPEED-S3 Volt 65 – 225 65
Pr60 M10 – 03 – 06 Heat exchanger 2 (ducting 1) in power 4 work phase DUCT.1 SPEED-S4 Volt 65 – 225 65
Pr61 M10 – 03 – 07 Heat exchanger 2 (ducting 1) in power 5 work phase DUCT.1 SPEED-S5 Volt 65 – 225 65
Pr62 M10 – 03 – 08 Heat exchanger 3 (ducting 2) in power 1 work phase DUCT.2 SPEED-S1 Volt 65 – 225 65
Pr63 M10 – 03 – 09 Heat exchanger 3 (ducting 2) in power 2 work phase DUCT.2 SPEED-S2 Volt 65 – 225 65
Pr64 M10 – 03 – 10 Heat exchanger 3 (ducting 2) in power 3 work phase DUCT.2 SPEED-S3 Volt 65 – 225 65
Pr65 M10 – 03 – 11 Heat exchanger 3 (ducting 2) in power 4 work phase DUCT.2 SPEED-S4 Volt 65 – 225 65
Pr66 M10 – 03 – 12 Heat exchanger 3 (ducting 2) in power 5 work phase DUCT.2 SPEED-S5 Volt 65 – 225 65
Parameters “VARIOUS SETTINGS” - Mod. DSA (L15_181119)
Parameter Menu level Description Display Measurement Value field
Database
P1
Pr38 M10 – 04 – 01 Re-ignition block RESTART BLOCK Minutes 0 – 10 5
Pr39 M10 – 04 – 02 Time for considering the device off OFF TIME Minutes 0 – 20 10
Pr40 M10 – 04 – 03 Pre-loading time in ignition PRE-LOAD START Seconds 0 – 255 210
Pr41 M10 – 04 – 04 Stand-by time after pre-loading AFTER PRE-LOAD Seconds 0 – 255 120
Pr42 M10 – 04 – 05 Extractor speed in pre-loading phase
PRE-LOAD SMOKE
SPEED
Rpm 350 – 2800 2100
Pr43 M10 – 04 – 06 Temperature delta on “SET ROOM” for automatic switching on/off DELTA ON-OFF °C
0.0 – 10.0 1.0
Pr44 M10 – 04 – 07 Automatic switch-off delay (timer after reaching “SET ROOM”) AUTO OFF DELAY Minutes
2 – 120 10
Pr45 M10 – 04 – 08 Power change delay POWER CHANGE Seconds 0 – 240 60
Pr46 M10 – 04 – 09 Heat exchanger 1 speed (primary) in the switch-off phase AIR SPEED OFF Volt
65 – 225 225
Pr47 M10 – 04 – 10 Keypad lock enable KEY LOCK On – Off On – Off Off
Pr48 M10 – 04 – 11 Time after which an alarm is triggered in the event of a blackout BLACK OUT TIME Seconds 0 – 60 30
Pr49 M10 – 04 – 12
Time after which the “NO PELLET” alarm triggers In case of “PELLET
RESERVE”
RESERVE ALARM Minutes 1 – 180 60
Pr50 M10 – 04 – 13 Enabling of the pellet level sensor (only on configured models) PELLET RESERVE On – Off On – Off Off