klover DIVA SLIM Installation, Use, Maintenance And Helpful Tips Download

Page: 7 / 52

DIVA SLIM AIR PELLET STOVE

EN - Rev. 1.0

Anti-interference filter.

Main switch, connection for

power supply cable with 2

built-in fuses (4A 250V).

Support panel.

Wi-Fi information
(MAC address and
registration code).

Safety thermostat with
manual reset.

R.T. terminal for room

main thermostat

connection.

FRONT VIEW

Serial Connector

to connect to the
Technical Assistance

Centre.

R.T. Terminal/Probe for

ducted room thermostat
connection / ducted room
probe connection.

Inspection Port

lower flue gas

passage.

Inspection Port
flue gas extractor
passage.

CE label

with technical data,

serial number and

model.

Flue gas extractor.

Flue pressure
switch.

Control unit.

Rod for cleaning the
front heat exchanger.

Summary of Contents for DIVA SLIM





















































Search results

Summary of Contents for DIVA SLIM

Reviews:

Related manuals for DIVA SLIM

Brands by name

Popular brands

klover DIVA SLIM, Installation, Use, Maintenance And Helpful Tips

Search results

Summary of Contents for DIVA SLIM

Reviews:

Related manuals for DIVA SLIM

Brands by name

Popular brands