manualshive.com logo in svg

klover DIVA SLIM, Installation, Use, Maintenance And Helpful Tips

Share
Download
klover DIVA SLIM Installation, Use, Maintenance And Helpful Tips Download Page 20

DIVA SLIM AIR PELLET STOVE 

 

18 

 

EN - Rev. 1.0 

The support panel allows for managing the basic functions concerning the appliance’s operation when there is no remote 

control.  

The following operations can therefore be carried out: 

-

 

SWITCHING ON/OFF: by pressing and holding button 1 (On/Off) for 2 seconds 

-

 

WORKING POWER CHANGE: whenever button 2 (Power) is pressed, the working power can be varied by selecting 

one of the three available power levels (1, 3 or 5). With the help of LEDs 2 and 3 (Power status), it is possible to 

verify which power level was chosen 

(see LED table)

. 

 

Display 

The remote control display shows information on the appliance’s operating status.  
 

The display can be switched on by pressing button 3 (On/Off). 

 

 

The underlying figure shows the display during normal operating conditions. 
 

 

 

 

By accessing the menu through button 4 (Set), it is possible to obtain various types of display modes and perform 

settings according to the selected menu. 

 
 

The figure below shows the display when the menus are being browsed. 

 

 

 

 

 

 

 

Room temperature 

Clock 

Operating status 

Power set in 
SET OUTPUT 

Summary of Contents for DIVA SLIM





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands