klover AURA 120, Installation, Use, Maintenance And Helpful Tips

Page: 54 / 68

49
AURA 80, CLASS 90, AURA 120, REA 100 PELLET-BURNING STOVE EN - Rev. 1.6
Parameter tables for AURA 80 MULTI-AIR / CLASS 90 MULTI-AIR
Parameters “CLEANER CALIBRATIONS” - Mod. AC80 / CLC90 (L09_161018)
Parameter Menu level Description Display Measurement Value field
Database
o2
Pr51 M10 – 01 – 01 ON time for brazier cleaning gear motor CLEANING TIME Seconds 0 – 120” 13
Pr52 M10 – 01 – 02 Time from switching off after which the brazier cleaning takes place CLEANER DELAY Minutes 1 – 15‘ 6
Pr53 M10 – 01 – 03 Time from switching on after which the brazier cleaning takes place CLEANER STAND-BY Hours 1 – 24 9
Parameters “DUCTING CALIBRATIONS” - Mod. AC80 / CLC90 (L09_161018)
Parameter Menu level Description Display Measurement Value field
Database
o2
Pr55 M10 – 03 – 01 Enable ducting function ENABLE DUC. Off / Mode
Off
S1 – S2 – S1+2
T1 – T2 – T1+2
A1 – A2 – A1+2
A1
Pr56 M10 – 03 – 02 Allows for choosing whether the ducted air fans can be switch “OFF”. OFF CANALIS- On / Off On / Off Off
Pr57 M10 – 03 – 03 Heat exchanger 2 speed (ducting 1) in power 1 work phase SPE. DUC. 1 – P.1 Volt 65 – 225 165
Pr58 M10 – 03 – 04 Heat exchanger 2 speed (ducting 1) in power 2 work phase SPE. DUC. 1 – P.2 Volt 65 – 225 175
Pr59 M10 – 03 – 05 Heat exchanger 2 speed (ducting 1) in power 3 work phase SPE. DUC. 1 – P.3 Volt 65 – 225 190
Pr60 M10 – 03 – 06 Heat exchanger 2 speed (ducting 1) in power 4 work phase SPE. DUC. 1 – P.4 Volt 65 – 225 220
Pr61 M10 – 03 – 07 Heat exchanger 2 speed (ducting 1) in power 5 work phase SPE. DUC. 1 – P.5 Volt 65 – 225 225
Pr62 M10 – 03 – 08 Heat exchanger 3 speed (ducting 2) in power 1 work phase SPE. DUC. 2 – P.1 Volt 65 – 225 65
Pr63 M10 – 03 – 09 Heat exchanger 3 speed (ducting 2) in power 2 work phase SPE. DUC. 2 – P.2 Volt 65 – 225 65
Pr64 M10 – 03 – 10 Heat exchanger 3 speed (ducting 2) in power 3 work phase SPE. DUC. 2 – P.3 Volt 65 – 225 65
Pr65 M10 – 03 – 11 Heat exchanger 3 speed (ducting 2) in power 4 work phase SPE. DUC. 2 – P.4 Volt 65 – 225 65
Pr66 M10 – 03 – 12 Heat exchanger 3 speed (ducting 2) in power 5 work phase SPE. DUC. 2 – P.5 Volt 65 – 225 65
Parameters “VARIOUS CALIBRATIONS” – Mod. AC80 / CLC90 (L09_161018)
Parameter Menu level Description Display Measurement Value field
Database
o2
Pr38 M10 – 04 – 01 Re-ignition block RE-IG BLOCK. Minutes 0 – 10 5
Pr39 M10 – 04 – 02 Time to consider the appliance off OFF TIME Minutes 0 – 20 10
Pr40 M10 – 04 – 03 Pre-loading time in ignition PRE-L IGNITION Seconds 0 – 255 210
Pr41 M10 – 04 – 04 Stand-by time after pre-loading
STAND-BY AFTER
PRE-L.
Seconds 0 – 255 230
Pr42 M10 – 04 – 05 Extractor speed in pre-loading phase SPE. F.GAS PRE. RPM 350 – 2800 2100
Pr43 M10 – 04 – 06 Temperature Delta on “SET ROOM” for automatic switching on/off DELTA ON-OFF °C
0.0 – 10.0 1.0
Pr44 M10 – 04 – 07 Automatic switch-off delay (timer after reaching “SET ROOM” ) DEL. OFF AUTO Minutes
2 – 120 10
Pr45 M10 – 04 – 08 Power change delay DEL. POW. CHANGE. Seconds
0 – 240 60
Pr46 M10 – 04 – 09 Speed of heat exchanger 1 (primary) during switching off SPE. AIR OFF Volt
65 – 225 225
Pr47 M10 – 04 – 10 Keypad lock enable KEY LOCK On – Off On – Off Off
Pr48 M10 – 04 – 11 Time after which an alarm is triggered in the event of a blackout BLACK OUT TIME Seconds 0 – 60 30
Pr49 M10 – 04 – 12 Time after which the alarm “NO PELLET” goes if“PELLET RESERVE” RESERVE ALARM Minutes 1 – 180 60
Pr50 M10 – 04 – 13 Enable pellet level sensor (on prepared models only) PELLET RESERVE On – Off On – Off Off
Parameters “FACTORY CALIBRATIONS” – Mod. AC80 / CLC90 (L09_161018)
Parameter Menu level Description Display Measurement Value field
Database
o2
Pr01 M10 – 05 – 01 Ignition cycle maximum time IGN. TIME Minutes 5 – 25 18
Pr02 M10 – 05 – 02 Flame stabilisation time following ignition STAB. TIME Minutes 0 – 15 9
Pr03 M10 – 05 – 03 Time interval between the two brazier cleaning operations INT. CLEAN Minutes 3 – 240 60
Pr04 M10 – 05 – 04 Screw feed gear motor ON time in ignition phase SC.F. IGNITION Seconds 0.1 – 8.0 0,8