manualshive.com logo in svg

Klein Marine Systems, Inc. HYDROCHART 3500, Operation And Maintenance Manual

Share
Download
Klein Marine Systems, Inc. HYDROCHART 3500 Operation And Maintenance Manual Download Page 74

C-2

   

APPENDIX C Compass Calibration

HydroChart 3500 Sonar System Operations and Maintenance Manual

P/N 11210087, Rev. 03

C.2 Setting up for the Compass Calibration

When setting up for the compass calibration, refer to Figure C-1 on page C-1. In 
addition, the cable harness is fabricated from a SubConn 5-pin bulkhead connector 
(P/N MCBH5F-SS) and an OceanServer digital compass cable (P/N 19-00061-24) 
which includes the DB9 connector and the battery pack. To fabricate the cable 
harness, cut off the small connector on the compass cable and splice the cut wires 
to the wires of the 5-pin bulkhead connector in accordance with Table C-1

.

To set up for the compass calibration:

1.

Connect the DB9 connector of the cable harness to the laptop PC and the 5-pin 
bulkhead connector to the cable of the compass assembly.

2.

Place the laptop PC, the cable harness with the battery pack, and the compass on 
the table or cart.

3.

Secure the compass with tape. It should be as level as possible.

C.3 Performing the Compass Calibration

To perform the compass calibration:

1.

Turn on the laptop PC and start the OS5000 Windows Compass Demo 
Program.

2.

Click 

Configure

.

The Setup dialog box opens as shown in Figure C-2.

Table C-1:  

Cable Harness 5-Pin Bulkhead Connector to DB9 and Battery 

Connectors Pin-to-Pin Connections

5-PIN BULKHEAD 

CONNECTOR PIN NO.

DB9 CONNECTOR PIN 

NO.

BATTERY 

TERMINAL

WIRE 

COLOR

1

—

Pos

Red

2

3

—

Blue

3

2

Green

4

5

Neg

Black

5

—

Summary of Contents for HYDROCHART 3500























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands