manualshive.com logo in svg

Klein Marine Systems, Inc. HYDROCHART 3500, Operation And Maintenance Manual

The Klein Marine Systems, Inc. HYDROCHART 3500 is a powerful and reliable hydrographic survey system. Ensure efficient usage with the comprehensive Operation And Maintenance Manual available for free download from our website. This manual provides detailed instructions and guidelines for the proper installation, operation, and maintenance of the product.

Share
Download
background image

Performing the Compass Calibration

C-3

3.

Select the input port from the 

Input Port

 drop-down list box.

4.

Select 19200 from the 

Baud Rate

 drop-down list box, and then click 

OK

.

5.

Click 

Program

.

The Program dialog box opens as shown in Figure C-3.

Figure C-2:  

Setup Dialog Box

Figure C-3:  

Program Dialog Box

Summary of Contents for HYDROCHART 3500























































































Reviews:

No comments

Related manuals for HYDROCHART 3500

Furuno FSV-84 Operator'S Manual preview
FSV-84
Brand: Furuno Pages: 240
Furuno DFF-3D Operator'S Manual preview
DFF-3D
Brand: Furuno Pages: 75

Brands by name

Popular brands

Load more brands