manualshive.com logo in svg

Klein Marine Systems, Inc. HYDROCHART 3500, Operation And Maintenance Manual

The Klein Marine Systems, Inc. HYDROCHART 3500 is a powerful and reliable hydrographic survey system. Ensure efficient usage with the comprehensive Operation And Maintenance Manual available for free download from our website. This manual provides detailed instructions and guidelines for the proper installation, operation, and maintenance of the product.

Share
Download
background image

C-1

APPENDIX C: C

OMPASS

 C

ALIBRATION

Although calibration of the OceanServer OS5000 Series Digital Compass is 
performed at the Klein Marine Systems, Inc. factory, it may be desirable to 
calibrate the compass to account for the differing magnetic fields in other parts of 
the world. Calibration can improve the accuracy of the compass readings.

C.1 Required Items

The following items, which are shown in Figure C-1, are required to perform the 

compass calibration:

• Compass assembly (P/N 14105534), removed from the frame. To 

remove and install the compass, refer to “Removing and Installing 

the Optional Compass” on page 4-13.

• Laptop PC with and available RS-232 serial port and OS5000 

Windows Compass Demo Program V2.6 installed, available as a 

download from www.ocean-server.com.

• Cable harness with 5-pin bulkhead and DB9 connectors and a 

3.6 V battery pack.

• Nonmetallic rotatable table or cart.

Figure C-1:  

Items and Setup Required for Compass Calibration

Laptop
computer

Battery
pack

Compass
assembly

DB9 connector

5-pin
bulkhead
connector

Summary of Contents for HYDROCHART 3500























































































Reviews:

No comments

Related manuals for HYDROCHART 3500

Marcum Technologies VX-1P User Manual preview
VX-1P
Brand: Marcum Technologies Pages: 8
Wesmar SS590 SERIES Installation & Operation Manual preview
SS590 SERIES
Brand: Wesmar Pages: 62
Eagle FISH I.D. AND PLUS Installation Instructions Manual preview
FISH I.D. AND PLUS
Brand: Eagle Pages: 16

Brands by name

Popular brands

Load more brands