manualshive.com logo in svg

Klein Marine Systems, Inc. HYDROCHART 3500, Operation And Maintenance Manual

Share
Download
Klein Marine Systems, Inc. HYDROCHART 3500 Operation And Maintenance Manual Download Page 28

3-4

   

CHAPTER 3 Setup and Test

HydroChart 3500 Sonar System Operations and Maintenance Manual

P/N 11210087, Rev. 03

To install the Sonar Head Unit:

1.

Align the bolt hole patterns and secure the mounting flange to the pipe flange 
using 3/8-16 stainless steel bolts. Be sure to maintain the long axis of the 
Sonar Head Unit parallel to the keel at all times. However, offsets can be 
corrected with a patch test as described in “Bathymetric System Calibration 
and Patch Test” on page 3-11.

NOTE  

When mounting the Sonar Head Unit, it is important to ensure that it 

is mounted correctly in the fore/aft direction. It should be oriented such that 
the arrow on the mounting flange points toward the bow as shown in 

Figure 3-3.

Figure 3-3:  

Arrow Label on the Sonar Head Unit Mounting Flange Should Point 

toward the Bow

WARNING  

In all of the remaining steps, be sure that the power is turned 

off and the TIU power cable is disconnected from the power source. Failure 
to follow this practice may result in personal injury or damage to the Sonar 

Head Unit or to the TIU electronics, or to both.

BOW

Summary of Contents for HYDROCHART 3500























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands