KitchenAid KSSC36FKB00 Technical Education Download Page 63 | Manualshive

Page: 63 / 76

background image

6-1

DIAGNOSIS & TROUBLESHOOTING

DIAGNOSIS

PRE-DIAGNOSTICS CHECKS

• Confirm the refrigerator and freezer tem-

peratures before beginning other checks.

• See if the compressor, evaporator, and

condenser fans are running.

• Check the position of the air door.

DIAGNOSTICS MODE

The Diagnostics Mode is used to:

• Check the refrigerator & freezer ther-

mistors.

• Operate the evaporator fan motor at 3000

rpm.

• Operate the condenser fan motor and com-

pressor.

• Check the defrost bimetal and heater.

To enter the Diagnostics Mode, the control
must be turned on, and be in a normal cooling
mode.

Power

On/Off

Warmer

Colder

Warmer

Colder

FREEZER

REFRIGERATOR

WATER FILTER

PERCENT LEFT

RESET

°

C

SELECT

Both the Power On/Off and the Water Filter
Reset keys must be functional. The refrigera-
tor display shows the step number. The results
of the checks are displayed on the water filter
status indicator. After 20 minutes, the control
will default from the Diagnostics Mode to a
normal cooling mode.

To enter the diagnostics mode:

• Press and hold the Water Filter Reset

keypad, and then immediately press and
hold the Power keypad. Continue to press
both keypads for 3 seconds, or until you
hear a beep.

To advance the diagnostics sequence:

• To advance to the next step in the se-

quence, press and hold the Water Filter
Reset key for 2 seconds, or until you hear
a beep. The Diagnostics Chart on the next
page shows the step number and the com-
ponent being tested in each step.

«
...
61
62
63
64
65
...
»

Summary of Contents for KSSC36FKB00













































































Reviews:

No comments

Related manuals for KSSC36FKB00

Brand: Samsung Pages: 8

Brand: Samsung Pages: 40

Brand: Samsung Pages: 84

Brand: Zanussi Electrolux Pages: 12

Brand: Samsung Pages: 39

Brand: TCL Pages: 44

Brand: Oster Pages: 32

FRS-U20DD Series

Brand: Daewoo Pages: 84

Brand: lec medical Pages: 18

Brand: Zerowatt Pages: 24

Brand: TERSO Pages: 15

Brand: Acqua Pages: 20

Brand: JUNO Pages: 12

Brand: Rangemaster Pages: 28

Brand: Perfect Aire Pages: 16

Brand: Daewoo Pages: 12

Brand: Gaggenau Pages: 24

Brand: Galaxy Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands