KitchenAid KSSC36FKB00 Technical Education Download Page 36

Page: 36 / 76

4-10

Lift and unhook the two evaporator cover
tabs, then lower the cover until the top
edge clears the air duct, and slide the
cover up and out of the freezer.

REMOVING THE BIMETAL, THE EVAPORATOR FAN

MOTOR, THE DEFROST HEATER, AND THE EVAPORATOR

NOTE:

Sharp edges may be present.

Unplug the refrigerator or disconnect the
power.

Open the freezer door.

Remove the freezer shelves that are over
the evaporator cover.

Remove the indicated two shelf mounting
studs.

Evaporator

Cover

Shelf Studs

Remove the eight hex-head screws from
the evaporator cover.

Screws

(2 of 8)

Unhook Evaporator

Cover Tabs

To remove the bimetal:

a) Unclip the bimetal from the evaporator

inlet tubing.

b) Follow the instructions that were sup-

plied with the replacement bimetal to
connect the wires.

Bimetal

Electrical Shock Hazard

Disconnect power before servicing.
Replace all panels before operating.
Failure to do so can result in death or
electrical shock.

Clip

Summary of Contents for KSSC36FKB00













































































Search results

Summary of Contents for KSSC36FKB00

Reviews:

Related manuals for KSSC36FKB00

Brands by name

Popular brands

KitchenAid KSSC36FKB00, Technical Education

Search results

Summary of Contents for KSSC36FKB00

Reviews:

Related manuals for KSSC36FKB00

Brands by name

Popular brands