KitchenAid KSSC36FKB00 Technical Education Download Page 44 | Manualshive

Page: 44 / 76

background image

4-18

REMOVING A THERMISTOR

NOTE:

Sharp edges may be present.

1.

Unplug the refrigerator or disconnect the
power.

NOTE: The refrigerator and freezer thermistors
are identical and are removed in the same
manner.

2.

Depending  on  the  thermistor,  open  the
freezer or refrigerator door, and remove
any  items from the shelf that are in front of
the  thermistor.  It  may  be  necessary  to
remove the shelf as well. The thermistor
locations are shown below.

Electrical Shock Hazard

Disconnect power before servicing.
Replace all panels before operating.
Failure to do so can result in death or
electrical shock.

4.

Disconnect the 2-wire connector and re-
move the thermistor.

3.

Remove the hex-head screw from the
thermistor cover. Pull the cover forward at
the screw end, and unhook the tab from
the slot at the other end of the thermistor
cover.

Refrigerator / Freezer

Thermistor Cover

Screw

Connector

Refrigerator / Freezer

Thermistor

Freezer Thermistor

Refrigerator Thermistor

«
...
42
43
44
45
46
...
»

Summary of Contents for KSSC36FKB00













































































Reviews:

No comments

Related manuals for KSSC36FKB00

GDM-HST02-HC-TSL01

Brand: True Manufacturing Company Pages: 28

Brand: McCall Pages: 2

Brand: True Pages: 2

Brand: Saba Pages: 32

Brand: Bauknecht Pages: 10

Brand: DAEWOO ELECTRONICS Pages: 20

Brand: SEVERIN Pages: 124

Brand: EuropAce Pages: 8

IntelliCold RLDF 19 Series

Brand: Labcold Pages: 15

Brand: NEFF Pages: 29

Brand: Haier Pages: 30

Brand: Haier Pages: 44

Brand: Haier Pages: 54

Brand: Haier Pages: 56

Brand: Haier Pages: 210

Brand: Haier Pages: 27

Brand: Haier Pages: 32

Brand: Haier Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands