KitchenAid KSSC36FKB00 Technical Education Download Page 53

Page: 53 / 76

4-27

h) Remove the hex-head screw from the

green ground wire on the water & ice
dispenser wiring harness.

d) Disconnect the water & ice dispenser

electrical harness connector at the back
of the refrigerator.

Water & Ice Dispenser
Electrical Harness Connector

Door Channel

Clip

f) Position a container to catch the water

in the next step.

e) Use a putty knife, slide the retainer clips

off the door channel, and pull the wiring
and water line out from under the chan-
nel.

g) Disconnect the water reservoir tubing

nut at the union and remove the nut
from the end of the tubing.

Water & Ice Dispenser
Electrical Harness

Water Reservoir

Union Nut

Harness Ground

Continued on the next page.

Electrical Shock Hazard

Connect green ground wire to ground
screw.
Failure to do so can result in death or
electrical shock.

Summary of Contents for KSSC36FKB00













































































Search results

Summary of Contents for KSSC36FKB00

Reviews:

Related manuals for KSSC36FKB00

Brands by name

Popular brands

KitchenAid KSSC36FKB00, Technical Education

Search results

Summary of Contents for KSSC36FKB00

Reviews:

Related manuals for KSSC36FKB00

Brands by name

Popular brands