KitchenAid KSSC36FKB00 Technical Education Download Page 2 | Manualshive

Page: 2 / 76

background image

- ii -

WHIRLPOOL CORPORATION assumes no responsibility for any repairs made
on our products by anyone other than Authorized Service Technicians.

FORWARD

This KitchenAid Job Aid, 2001 K Model Built-In Side-By-Side Refrigerator With Variable Capacity
Compressor (Part No. 4317326A), provides the technician with information on the installation and
service of the Built-In Side-By-Side Refrigerator. It is to be used as a training Job Aid and Service
Manual. For specific information on the model being serviced, refer to the “Use and Care Guide,”
or “Tech Sheet” provided with the refrigerator.

The Wiring Diagrams and Strip Circuits used in this Job Aid are typical and should be used for
training purposes only. Always use the Wiring Diagram supplied with the product when servicing
the unit.

GOALS AND OBJECTIVES

The goal of this Job Aid is to provide detailed information that will enable the service technician to
properly diagnose malfunctions and repair the Built-In Side-By-Side Refrigerator.

The objectives of this Job Aid are to:

• Understand and follow proper safety precautions.
• Successfully troubleshoot and diagnose malfunctions.
• Successfully perform necessary repairs.
• Successfully return the refrigerator to its proper operational status.

Copyright © 2002, Whirlpool Corporation, Benton Harbor, MI 49022

«
1
2
3
4
...
»

Summary of Contents for KSSC36FKB00













































































Reviews:

No comments

Related manuals for KSSC36FKB00

Brand: KegLand Pages: 13

Brand: Koncar Pages: 69

Brand: Häfele Pages: 53

CombiCooler V4000 178KNI

Brand: V-ZUG Pages: 40

Brand: Cylinda Pages: 86

Brand: Klarstein Pages: 16

Brand: NEFF Pages: 37

JUD24FR*S series

Brand: Jenn-Air Pages: 56

Brand: Blomberg Pages: 20

Brand: Blomberg Pages: 28

Brand: Hoover Pages: 32

Brand: Vitara Pages: 26

Brand: Smeg Pages: 13

Brand: Amica Pages: 60

El Presidente 23

Brand: Klarstein Pages: 40

Brand: Smeg Pages: 16

Brand: Danby Pages: 48

Brand: IKEA Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands