KitchenAid KSSC36FKB00 Technical Education Download Page 50

Page: 50 / 76

4-24

c) Disconnect the three wire connectors

and remove the subpanel.

b) Remove the two hex-head screws from

the switch subpanel, pull the panel for-
ward, and turn it over.

Hex-Head Screws

2 Wire Connectors

Wire Connector

c) Repeat the previous step for the other

corner of the front panel.

d) Pull the bottom of the front panel out

and then down to remove it from the
dispenser.

To remove the dispenser:

a) Disconnect the front panel wire con-

nector and remove the panel.

REASSEMBLY NOTE: To reinstall the front
panel on stainless steel trimless doors:

Fit the top edge of the panel into the door
opening.

Place a folded towel over the top edge of
the panel and hit it with the rubber mallet
you used earlier to seat it in the door.

Place the folded towel along the bottom
edge of the front panel and seat it with the
mallet.

Seat This Area Last

Seat This Area First

Summary of Contents for KSSC36FKB00













































































Search results

Summary of Contents for KSSC36FKB00

Reviews:

Related manuals for KSSC36FKB00

Brands by name

Popular brands

KitchenAid KSSC36FKB00, Technical Education

Search results

Summary of Contents for KSSC36FKB00

Reviews:

Related manuals for KSSC36FKB00

Brands by name

Popular brands