KitchenAid KBFC42FS Technical Education Download Page 39

Page: 39 / 76

4-17

REMOVING A REFRIGERATOR DOOR SWITCH

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death or
electrical shock.

3. Remove the two hex-head screws from

the door switch cover and remove the
cover.

WARNING

1. Unplug refrigerator or disconnect power.
2. Lift the top grille off the pins at each end

and remove the grille.

Top Grille

4. Disconnect the two wires from the door

switch terminals.

Door Switch

Cover Screws

5. Fully open the refrigerator door.
6. Push the bottom of the door switch out as

far as it will go, then press down on the
top locking tab, and push the switch out
of the bracket.

Door Switch

Wires

Door Switches

Push Out

Door Switch

Locking Tab

Summary of Contents for KBFC42FS













































































Search results

Summary of Contents for KBFC42FS

Reviews:

Related manuals for KBFC42FS

Brands by name

Popular brands

KitchenAid KBFC42FS, Technical Education

Search results

Summary of Contents for KBFC42FS

Reviews:

Related manuals for KBFC42FS

Brands by name

Popular brands