KitchenAid KBFC42FS Technical Education Download Page 27 | Manualshive

Page: 27 / 76

background image

4-5

REMOVING THE REFRIGERATOR THERMISTOR

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death or
electrical shock.

1. Unplug refrigerator or disconnect power.
2. If needed, remove the food and racks from

the upper shelf.

WARNING

4. Unlock and disconnect the refrigerator

thermistor connector from the wiring har-
ness and remove the thermistor.

Refrigerator Thermistor

3. Remove the hex-head screw from the re-

frigerator thermistor and pull the thermis-
tor away from the liner.

Refrigerator

Thermistor Screw

Refrigerator

Thermistor

Connector

«
...
25
26
27
28
29
...
»

Summary of Contents for KBFC42FS













































































Reviews:

No comments

Related manuals for KBFC42FS

Brand: Samsung Pages: 2

Brand: Avanti Pages: 28

Brand: Igloo Pages: 11

Brand: NEFF Pages: 105

Brand: Blomberg Pages: 25

Brand: Bartscher Pages: 28

Brand: Gram Pages: 112

Brand: Avanti Pages: 21

Brand: Ugur Pages: 45

Brand: Smoko Pages: 4

Brand: Zanussi Electrolux Pages: 16

Brand: Oursson Pages: 28

RFG237AAPN - 23 cu. ft. Refrigerator

Brand: Samsung Pages: 50

Brand: Samsung Pages: 50

Brand: Samsung Pages: 84

Brand: Samsung Pages: 160

Brand: Samsung Pages: 428

Brand: Samsung Pages: 428

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands