KitchenAid KBFC42FS Technical Education Download Page 41

Page: 41 / 76

4-19

REMOVING A REFRIGERATOR DOOR

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death or
electrical shock.

1. Unplug refrigerator or disconnect power.
2. Pull the freezer drawer open and remove

the T-15 stop screw from the bottom
hinge pin.

WARNING

3. Lift the top grille and remove it.

Bottom Stop

Screw

Top Grille

4. With the door closed, unhook the door

spring and remove it (see the top right
photo).

5. Remove the screw from the door stop.

IMPORTANT NOTE:

Support the door in the

next step so that it does not fall.
6. Open the door and remove the three

screws from the top hinge leaf.

Screw

Top Hinge Screws

7. Pull the top of the door

forward, and remove
the top hinge pin bracket
and spacer. Lift the door
so the bottom hinge pin
is free of the hinge plate,
and remove the door.

Ends Of

Door Spring

Summary of Contents for KBFC42FS













































































Search results

Summary of Contents for KBFC42FS

Reviews:

Related manuals for KBFC42FS

Brands by name

Popular brands

KitchenAid KBFC42FS, Technical Education

Search results

Summary of Contents for KBFC42FS

Reviews:

Related manuals for KBFC42FS

Brands by name

Popular brands