KitchenAid KBFC42FS Technical Education Download Page 28

Page: 28 / 76

4-6

REMOVING THE REFRIGERATOR

MOTORIZED AIR DOOR

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death or
electrical shock.

1. Unplug refrigerator or disconnect power.
2. If needed, remove the food and racks

from the upper shelf.

WARNING

5. Unlock and disconnect the motorized air

door connector from the wiring harness
and remove the air door and cover.

6. Peel off the adhesive covering from over

the motorized air door, and remove the
air door from the cover.

Motorized Air Door

3. Remove the three hex-head screws from

the motorized air door cover.

4. Pull down on the motorized air door cover

to unhook it from the rear clips and turn it
over.

Motorized Air Door Cover Screws

Motorized Air

Door Connector

Adhesive Covering

Refrigerator

Motorized Air Door

Summary of Contents for KBFC42FS













































































Search results

Summary of Contents for KBFC42FS

Reviews:

Related manuals for KBFC42FS

Brands by name

Popular brands

KitchenAid KBFC42FS, Technical Education

Search results

Summary of Contents for KBFC42FS

Reviews:

Related manuals for KBFC42FS

Brands by name

Popular brands