KitchenAid KBFC42FS Technical Education Download Page 51 | Manualshive

Page: 51 / 76

background image

4-29

10.

To remove the evaporator:

a) Remove the bimetal (see step 8).
b) Remove the defrost heater (see step 9).
c) Remove the foam air block from the

left side of the evaporator.

d) Remove the two hex-head screws from

the bottom of the evaporator.

e)

IMPORTANT:

Refrigerant must be

handled  by  a  licensed,  EPA-certified
refrigerant  technician  in  accordance
with established procedures. Remove
the  refrigerant  from  the  existing  sys-
tem per the instructions provided with
the recovery system being used.

f) Unbraze the tubing and remove the

evaporator.

Screw

Screw

Evaporator

Unbraze Tubing

Foam Air

Block

«
...
49
50
51
52
53
...
»

Summary of Contents for KBFC42FS













































































Reviews:

No comments

Related manuals for KBFC42FS

Brand: KegLand Pages: 13

Brand: Randell Pages: 2

Brand: Randell Pages: 20

Brand: Randell Pages: 2

Brand: Elkay Pages: 2

Brand: Jenn-Air Pages: 13

Brand: Inoksan Pages: 42

Silhouette Select SSBC056D1B

Brand: Danby Pages: 28

Brand: U-Line Pages: 47

Brand: Kalamera Pages: 11

Brand: True Pages: 2

Brand: Grundig Pages: 98

Brand: Iceking Pages: 20

Brand: Saivod Pages: 81

Brand: Saivod Pages: 92

Brand: Saivod Pages: 71

Brand: Zanussi Pages: 12

Brand: Zanussi Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands