Before you start...
It is the customer’s responsibility:
• To contact a qualified electrical installer.
• To assure that electrical installation is
adequate and in conformance with
National Electrical Code, ANSI/NFPA
70 — latest edition**, or CSA Standard,
C22.1 Canadian Electrical Code, Part 1 —
latest edition*, and all local codes and
ordinances.
Cabinet opening dimensions shown must
be used. Given dimensions are minimum
clearances.
When installing a range under existing
cabinets and installation does not meet
the minimum cabinet clearances, install a
range hood above the range to avoid
burn hazards.
NOTE:
Some cabinet and building
materials are not designed to withstand
the heat produced by the oven for baking
and self-cleaning. Check with your
builder or cabinet supplier to make sure
that the materials used will not discolor,
delaminate or sustain other damage.
All openings in the wall or floor where
the range is to be installed must be
sealed.
It is recommended that a range hood be
installed above this range.
IMPORTANT:
Observe all governing
codes and ordinances.
NOTE:
The range cooktop is
manufactured for use with Natural gas.
To convert to L.P./Propane gas, see the
Gas Conversion instructions provided in
literature package.
Proper gas and electrical supply
connections must be available. See “Gas
supply requirements,” Page 4 and
“Electrical requirements,” Page 5.
Do not obstruct flow of combustion and
ventilation air.
Proper installation is your responsibility.
Have a qualified technician install this
range. Make sure you have everything
necessary for correct installation. It is the
installer's responsibility to comply with
the installation clearances specified on
the gas information label. The gas
information label and model/serial rating
plate are located on the surface below
the control panel.
This installation must conform with all
local codes and ordinances. In the
absence of local codes, installation must
conform with American National
Standard, National Fuel Gas Code ANSI
Z223.1 — latest edition* or CAN/CGA —
B149 — latest edition* installation codes.
WARNING: If the
information in this manual
is not followed exactly, a
fire or explosion may result
causing property damage,
personal injury or death.
— Do not store or use
gasoline or other
flammable vapors and
liquids in the vicinity of
this or any other
appliance.
— WHAT TO DO IF YOU
SMELL GAS
• Do not try to light any
appliance.
• Do not touch any
electrical switch.
• Do not use any phone in
your building.
• Immediately call your
gas supplier from a
neighbor’s phone. Follow
the gas supplier’s
instructions.
• If you cannot reach your
gas supplier, call the fire
department.
— Installation and service
must be performed by a
qualified installer, service
agency or the gas
supplier.
2
Copies of the standards listed may be
obtained from:
* CSA International
8501 East Pleasant Valley Road
Cleveland, Ohio 44131-5575
** National Fire Protection Association
One Batterymarch Park
Quincy, Massachusetts 02269
WARNING
Your safety and the safety of
others are very important.
You can be killed or seriously injured
if you don't
follow
instructions.
You can be killed or seriously injured
if you don't follow instructions.
We have provided many important safety
messages in this manual and on your
appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to
potential hazards that can kill
or hurt you and others.
All safety messages will follow the safety
alert symbol and either the word
“DANGER” or “WARNING.” These
words mean:
All safety messages will tell you what the
potential hazard is, tell you how to
reduce the chance of injury, and tell you
what can happen if the instructions are
not followed.
immediately
DANGER
In the State of Massachusetts, the
following installation instructions
apply:
• Installations and repairs must be
performed by a qualified or licensed
contractor, plumber, or gasfitter
qualified or licensed by the State of
Massachusetts.
• If using a ball valve, it shall be a
T-handle type.
• A flexible gas connector, when used,
must not exceed 3 feet.
