KidKraft Cedar Summit F25745 Installation And Operating Instructions Manual Download

Page: 74 / 135

Step 35: Assemble and Attach BBQ Kitchen

Part 2

Hardware

Other Parts

4 x

#8 x 7/8” Truss Screw

1 x BBQ Cooktop

1 x BBQ Sink Set

Fig. 35.6

Fig. 35.7
Top View

Faucet

Sink

Knob

Sink

Sink Knob

Included

hardware

Fig. 35.5

Tight

BBQ

Sink Set

BBQ

Sink Set

BBQ Base

BBQ

Cooktop

BBQ

Cooktop

Fig. 35.8

Fig. 35.9

182

BBQ Base

Place Faucet and 2 Sink Knobs in opening of Sink and attach Sink Knobs with included hardware. (fig. 35.5)

Important: Use a hand held screw driver and DO NOT over tighten.

Slide BBQ Cooktop tight beside BBQ Base on the left and BBQ Sink Set tight on the right. Attach both BBQ

Cooktop and BBQ Sink Set to (182) Table Top with 2 (S0) #8 x 7/8” Truss Screws each. (fig. 35.6, 35.7, 35.8 and

35.9)

Summary of Contents for Cedar Summit F25745








































































































































Search results

Summary of Contents for Cedar Summit F25745

Reviews:

Related manuals for Cedar Summit F25745

Brands by name

Popular brands

KidKraft Cedar Summit F25745, Installation And Operating Instructions Manual

Search results

Summary of Contents for Cedar Summit F25745

Reviews:

Related manuals for Cedar Summit F25745

Brands by name

Popular brands