manualshive.com logo in svg

KidKraft Cedar Summit F25745, Installation And Operating Instructions Manual

Share
Download
KidKraft Cedar Summit F25745 Installation And Operating Instructions Manual Download Page 28

 28 

 

  

6 places

#8 x 1-1/2" Wood Screw

52042512

5/16 x 1-3/8" Wafer Head Bolt w/ Nylok

5/16" Flat Washer

Narrow Wall A

609214

Narrow Wall C

609216

Narrow Wall Cross

609220

Narrow Wall Cross

609220

Narrow Wall Angled Cross

609219

Narrow Wall D

609217

6 places

#8 x 1-1/2" Wood Screw

52042512

5/16 x 1-3/8" Wafer Head Bolt w/ Nylok

5/16" Flat Washer

Narrow Wall A

609214

Narrow Wall C

609216

Narrow Wall Cross

609220

Narrow Wall Cross

609220

Narrow Wall Angled Cross

609219

Narrow Wall D

609217

6 places

#8 x 1-1/2" Wood Screw

52042512

5/16 x 1-3/8" Wafer Head Bolt w/ Nylok

5/16" Flat Washer

Narrow Wall A

609214

Narrow Wall C

609216

Narrow Wall Cross

609220

Narrow Wall Cross

609220

Narrow Wall Angled Cross

609219

Narrow Wall D

609217

6 places

#8 x 1-1/2" Wood Screw

52042512

5/16 x 1-3/8" Wafer Head Bolt w/ Nylok

5/16" Flat Washer

Narrow Wall A

609214

Narrow Wall C

609216

Narrow Wall Cross

609220

Narrow Wall Cross

609220

Narrow Wall Angled Cross

609219

Narrow Wall D

609217

1 x 

Rock Wall H 1-1/4 x 2-1/4 x 75-63/64”

1 x 

Narrow Wall D 1-1/4 x 2-1/4 x 52-49/64”

1 x 

Narrow Wall A 1-1/4 x 2-1/4 x 84”

2 x 

Narrow Wall Cross 1-1/4 x 3 x 8-3/32”

1 x 

Narrow Wall Angled Cross 1-1/4 x 3 x 11-1/4”

Step 6:  Narrow Wall Frame Assembly

Wood Parts

051

064

065

057

062

A:

  Place (051) Rock Wall H and (062) Narrow Wall D together so that they are connected at the notched ends. 

Attach using 1 (H10) 1/4 x 2-1/4” Hex Bolt (with lock washer, flat washer and t-nut). (Fig. 6.1 and 6.2) 

B:

  Place (057) Narrow Wall A on the left side of the frame assembly so that the top ends of the boards line up, 

making sure to note hole orientation. Place 1 (064) Narrow Wall Cross in each of the 2 locations shown in fig. 

6.3 and attach using 2 (WB2) 5/16 x 1-3/8” Wafer Head Bolts (with flat washer and t-nut) and 4 (S20) #8 x 1-3/8” 

Wood Screws per board. (Fig. 6.3 and 6.4) 

C:

  Place (065) Narrow Wall Angled Cross as shown in fig. 6.3 and attach using 2 (WB2) 5/16 x 1-3/8” Wafer Head 

Bolts (with flat washer and t-nut) and 4 (S20) #8 x 1-3/8” Wood Screws per board. (Fig. 6.3 and 6.4)

Fig. 6.1

051

057

057

064

065

065

062

062

S20

Fig. 6.2

Fig. 6.3

Fig. 6.4

Rock Wall frame, front view

8 Places

4 Places

beveled edge on this side for all horizontal boards

H10

1/4” lock 

washer

Note hole 

orientation

1/4” flat 

washer

1/4” 

t-nut

051

Narrow Rock 

Wall Frame, 

Front View

WB2

5/16” 

t-nut

5/16” flat 

washer

Hardware

12 x 

#8 x 1-3/8” Wood Screw

1 x 

5/16 x 1-3/8” Hex Bolt (with 1/4” lock washer,   

                1/4” flat washer and 1/4” t-nut)
6 x 

5/16 x 1-3/8” Wafer Head Bolt 

                (5/16” flat washer, 5/16” t-nut)

S20

H10

WB2

Summary of Contents for Cedar Summit F25745








































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands