Keysight M9502A User Manual Download

Page: 78 / 142

Keysight M9502A/M9505A AXIe Chassis User Guide

Features and Functions

Shelf Management Functions

All AXIe chassis provide these ATCA shelf management functions:

Monitor and control chassis fan speed

Monitor chassis backplane temperature

Monitor module health, as provided by the module vendor (may include
voltages and temperatures, fuse status, alarms and alarm setpoints)

Automatically and safely shutdown power upon a fan tray or power supply
unit (PSU) failure

You may monitor chassis behavior and make fan settings as explained below
using the chassis

Web Interface

, on the

Chassis Health

page.

Shelf management is implemented in the ESM firmware. You may upgrade
firmware through the base interface (LAN) connection.

To Monitor Fans:

You can check the individual chassis fan speeds, fan levels, and status. The fan
speeds are listed under the Chassis header in the

Sensors

section of the Chassis

Health page.

Summary of Contents for M9502A















































































































































Search results

Summary of Contents for M9502A

Reviews:

Related manuals for M9502A

Brands by name

Popular brands

Keysight M9502A, User Manual

Search results

Summary of Contents for M9502A

Reviews:

Related manuals for M9502A

Brands by name

Popular brands