36
Upgrade Kits
Upgrade kits for the PNA Series
E8362B, E8363B, E8364B, E8361A, N5250A
3
Upgrade kits are available to add options after initial pur-
chase. To order an upgrade kit for the PNA series, order the
analyzer’s model number followed by a “U”, then indicate
the option to be added (for example, E8362BU-010). The
serial number of the instrument to be retrofitted is required
as part of the order.
–
Time-domain
(Option 010) User installable.
–
Configurable test set
(Option 014)
Provides six front-panel RF access loops.
Includes installation at a Keysight service center.
–
Receiver attenuators
(Option 016)
Includes installation at a Keysight service center.
–
Extended memory
(Option 022)
Applies only to E8362B/63B/64B/61A with 256 MB of RAM.
Includes installation at a Keysight service center.
–
Frequency range upgrade to an E8363B (40 GHz) PNA
(Option 04/41)
Available only for the E8362A/B. Includes installation at a Keysight
service center.
–
Frequency range upgrade to an E8364B (50 GHz) PNA
(Option 05/51)
Available only for the E8362A/B and E8363A/B
Includes installation at a Keysight service center.
–
Frequency range upgrade to an E8361A (67 GHz) PNA
(Option 067/068))
Available only for the E8363B and E8364B.
Includes installation at a Keysight service center.
–
Frequency-offset
(Option 080)
Includes installation at a Keysight service center.
–
External reference switch
(Option 081)
Includes installation at a Keysight service center.
–
Scalar-calibrated converter measurements
(Option 082)
User installable. Option 080 required.
–
Frequency converter measurement application
(Option 083)
User installable. Option 080 and 081 required.
–
Embedded LO measurements
(Option 084)
Advanced software tuning that provides absolute group delay
of converters with embedded LOs without the need for access to a
common reference signal. The measurement result is the
and above plus 1.1 GHz CPU board.
–
4-port measurement application
(Option 550)
Enables full 4-port error correction and differential measurements.
Option 014 and external test set required. User installable.
–
N-port capabilities
(Option 551)
Adds full N-port error correction and measurement capabilities.
Option 014 and external test set required. User installable.
–
Extended power range
(Option UNL)
Adds a step attenuator and a bias-tee between source and each
test port. Includes installation at a Keysight service center.
–
Pulsed-RF measurement capability
(Option H08)
Provides software to set up and control pulsed-RF measurements
using narrowband detection, with point-in-pulse and pulse-
profile capability. User installable.
–
IF access
(Option H11)
Provides hardware for antenna, point-in-pulse, and millimeter-
wave measurements. Adds rear-panel RF and LO outputs, external
IF inputs, and IF gates (gates enabled with Option H08). Includes
installation at a Keysight service center.
–
High-power test set
(Option H85)
1
Removes bias tees for higher test port power-handling capability.
Options UNL, 014, 016, 080, and 081 are required. Includes
installation at a Keysight Service Center.
–
Upgrade to C model
2
(Option 221 or Option 241)
Provides new front panel, new hard drive with latest firmware and
new GUI. Option 221 is available for the E8361A, E8362/3 /4B, and
N5230A 2-port instruments. Option 241 is available for N5230A
4-port instruments.
1. Please contact Keysight for ordering this upgrade.
2. Some older PNAs may also require the purchase of a new CPU board.
3. For N5250A upgrades, order E8361AU options.
