Keysight Technologies N5221B Manual Download Page 57

Page: 57 / 88

Installation Note N5222-90131 57

Description of the Upgrade
Installation Procedure for the Upgrade

—

➁

— W75 (N5222-20002) A26 port 3 receiver coupler to A35 port 3 source

attenuator)

—

➂

— W90 (N5222-20006) A43 port 3 receiver attenuator to A24 mixer brick

(C)

—

➃

— W18 (N5222-20042) W7 to A27 port 4 receiver coupler

—

➄

– W90 (N5222-20041) W5 to A26 port 3 receiver coupler

—

⑥

— W38 (N5222-20024) REF 3 RCVR R3 IN to A24 mixer brick (R3)

Refer to

Figure 40 on page 67

—

①

— W37 (N5222-20101) A33 reference mixer switch to A23 mixer brick

(R1)

— W35 (reuse) (N5222-20033) A33 reference mixer switch to front-panel REF

1 SOURCE OUT
* Refer to the note shown in

Figure 33

for information on installing W36

(part number N5222-20032).

— W36 (reuse) (N5222-20032) REF 1 RCVR R1 IN to A33 reference mixer

switch
* Refer to the note shown in

Figure 33

for information on installing W36

(part number N5222-20032).

Summary of Contents for N5221B

























































































Search results

Summary of Contents for N5221B

Reviews:

Related manuals for N5221B

Brands by name

Popular brands

Keysight Technologies N5221B, Manual

Search results

Summary of Contents for N5221B

Reviews:

Related manuals for N5221B

Brands by name

Popular brands