Keysight Technologies N5221B Manual Download Page 13

Page: 13 / 88

Installation Note N5222-90131 13

Description of the Upgrade
Items Included in the Upgrade Kit

RF cable, W5 to A26 port 3 receiver coupler

N5222-20041

RF cable, A8 source (2) board P3 to W8 on bottom of analyzer – Top Cable

N5222-20063

RF cable, W7 to A23 port 4 receiver coupler

N5222-20042

W14

RF cable, A29 port 1 coupler to front-panel Port 1 CPLR ARM

N5222-20030

W17

RF cable, A26 port 3 receiver coupler to front-panel REF 3 SOURCE OUT

N5222-20023

W18

RF cable, A30 port 3 coupler to front-panel Port 3 CPLR ARM

N5222-20015

W21

RF cable, A23 port 4 receiver coupler to front-panel REF 4 SOURCE OUT

N5222-20025

W22

RF cable, A31 port 4 coupler to front-panel Port 4 CPLR ARM

N5222-20018

W26

RF cable, A32 port 2 coupler to front-panel Port 2 CPLR ARM

N5222-20034

W30

RF cable, Front panel jumper

N5222-20091

W37

A33 reference mixer switch to A23 mixer brick (R1)

N5222-20101

W38

REF 3 RCVR R3 IN to A24 mixer brick (R3)

N5222-20024

W39

REF 4 RCVR R4 IN to A24 mixer brick (R4)

N5222-20027

W42

RF cable, A21 HMA26.5 to A22 splitter

N5222-20009

W43

RF cable, A22 splitter to A23 mixer brick

N5222-20007

W44

RF cable, A22 splitter to A24 mixer brick

N5222-20008

W52

RF cable, A23 mixer brick (R1) to A20 IF multiplexer (P411)

N5242-60021

W53

RF cable, A23 mixer brick (R2) to A20 IF multiplexer (P412)

N5242-60022

W55

RF cable, A24 mixer brick (D) to A20 IF multiplexer (P801)

N5242-60024

W56

RF cable, A24 mixer brick (R4) to A20 IF multiplexer (P414)

N5242-60019

W57

RF cable, A24 mixer brick (R3) to A20 IF multiplexer (P413)

N5242-60020

W58

RF cable, A24 mixer brick (C) to A20 IF multiplexer (P601)

N5242-60023

W60

RF cable, A20 IF multiplexer board P203 to A12 SPAM board (J2)

N5242-60013

W62

RF cable, A20 IF multiplexer board P603 to A12 SPAM board (J5)

N5242-60015

W71

A25 port 1 receiver coupler to A34 port 1 source attenuator

N5222-20002

W76

A35 port 3 source attenuator to front-panel Port 3 SOURCE OUT

N5222-20019

W79

A27 port 4 receiver coupler to A36 port 4 source attenuator

N5222-20001

W80

A36 port 4 source attenuator to front-panel Port 4 SOURCE OUT

N5222-20020

W89

Port 3 RCVR C IN to A43 port 3 receiver attenuator

N5222-20021

Table 2

Contents of Upgrade Kit N5222-60131

Ref

Desig.

Description

Qty

Part Number

Summary of Contents for N5221B

























































































Search results

Summary of Contents for N5221B

Reviews:

Related manuals for N5221B

Brands by name

Popular brands

Keysight Technologies N5221B, Manual

Search results

Summary of Contents for N5221B

Reviews:

Related manuals for N5221B

Brands by name

Popular brands