Keysight Technologies N5221B Manual Download Page 81

Page: 81 / 88

Installation Note N5222-90131 81

Description of the Upgrade
Installation Procedure for the Upgrade

Step 51. Enable Option 420

Procedure Requirements

— The analyzer must be powered up and operating to perform this procedure.
— The Network Analyzer program must

not

be running.

— Refer to the license message you received from Keysight: Verify that the

analyzer’s model and serial numbers match those on the license message

you received from Keysight.

— A keyboard must be connected to the network analyzer.

Option Enable Procedure

Locate the email(s) from Keysight which contain license file attachments.

These emails are a result of

“License Key Redemption” on page 6

Copy the license file(s) from the email(s) to the

root directory

of the USB

flash drive.

More than one license file may be copied to the USB flash drive.

Insert the USB flash drive into the PNA’s USB drive slot.

Verifying and editing the license file:
For these steps, refer to the example in

Figure 49 on page 82

Verify your USB flash drive is connected to a PC.

Open your license file using a text read/write program similar to

Notepad.

If you have more than one licensed feature, delete the feature that is

not

required for this upgrade. (e.g., in this case N5242B-423 is the

correct upgrade. So, N5242B-422 is to be deleted from the text file.)

For this step, you will need a USB flash drive.
A single license file may contain more than one feature.

A single license file may contain more than one feature.

Summary of Contents for N5221B

























































































Search results

Summary of Contents for N5221B

Reviews:

Related manuals for N5221B

Brands by name

Popular brands

Keysight Technologies N5221B, Manual

Search results

Summary of Contents for N5221B

Reviews:

Related manuals for N5221B

Brands by name

Popular brands