Keysight Technologies N5221B Manual Download Page 58

Page: 58 / 88

58 Installation Note N5222-90131

Description of the Upgrade
Installation Procedure for the Upgrade

Figure 33

Information to Secure W35 and W36 (Option 419 shown, but Option 420 is

similar) - (N5222-20032, N5222-20033)

— W13 (reuse) (N5222-20005) A25 port 1 receiver coupler to A33 reference

mixer switch
* If the screws that attach the reference mixer switch to the test set deck

were loosened, torque these screws now to 9 in-lbs.

— W10 (reuse) (N5222-20043) W9 to A28 port 2 receiver coupler
— W8 (N5222-20042) W7 to A27 port 4 receiver coupler
— W6 (N5222-20041) W5 to A26 port 3 receiver coupler
— W4 (reuse) (N5222-20040) W3 to A25 port 1 receiver coupler

Install New Cable(s) – A2 1 HMA26.5 to A23/A24 Mixer Bricks

If your instrument has a new HMA26.5 (N5240-60101) installed:
If you have a legacy HMA26.5 (5087-7765) installed, you can discard this

cable.

Summary of Contents for N5221B

























































































Search results

Summary of Contents for N5221B

Reviews:

Related manuals for N5221B

Brands by name

Popular brands

Keysight Technologies N5221B, Manual

Search results

Summary of Contents for N5221B

Reviews:

Related manuals for N5221B

Brands by name

Popular brands