Keysight Technologies N5221B Manual Download Page 12

Page: 12 / 88

12 Installation Note N5222-90131

Description of the Upgrade
Items Included in the Upgrade Kit

Machine screw, M2.5 x 20, pan head (to attach A26 and A27 receiver coupler

assemblies to test set deck)

0515-0430

Machine screw, M3.0 x 14, pan head (to install A70 low band board)

0515-0665

Machine screw, M3.0 x 18, pan head

0515-0666

Machine screw, M3 x 6, pan head (to attach bias T combiners to brackets)

0515-1227

Machine screw, M3.0 x 20, pan head (to attach brackets to receiver couplers; to

attach A24 mixer brick to block)

0515-1410

Machine screw, M3.0 x 6, flat head (to attach dress panel to coupler plate)

0515-1946

Machine screw, M2.5 x 14, pan head

0515-2141

Machine screw, M3.0 x 14, pan head (to attach splitter to mixer brick (2) and to

attach bias tees to bracket)

0515-2994

Cap – coaxial (SMA)

0960-0055

Bulkhead connector for test set front plate (hardware supplied with connector)

1250-3805

Nuts – flanged

5022-1087

Clamp – SMP (port 3 and port 4 bias combiners)

5023-3299

Cable, assembly, coaxial A06/A06, 205 mm long (Connect to A70 LFE board)

8120-5017

Cable assembly, flat ribbon

8120-0982

Gel pad (between each test coupler and the test set front plate)

E4403-20033

Subpanel, test set – 4-port

N5221-00007

Dress panel, lower – 4-port

N5240-00009

Vibration mount (between couplers 1 & 3, and 2 & 4)

0460-2725

Cable guard, center jumper cables

N5242-00049

Cable clamp

1400-1334

Cable clamp (12.9 mm wide)

1400-1391

Dust caps for test ports

1401-0214

Bracket for receiver coupler

N5242-00006

Bracket for attenuator

N5242-00007

RF cable, A11 13.5 GHz (SRC 2) direct digital synthesizer (J6)-SRC 2 RF IN P1– (This

cable replaces W2 N5222-20090)

N5240-20123

RF cable, A8 source (2) board P5 to W6 on bottom of analyzer – Top Cable

N5222-20062

Table 2

Contents of Upgrade Kit N5222-60131

Ref

Desig.

Description

Qty

Part Number

Summary of Contents for N5221B

























































































Search results

Summary of Contents for N5221B

Reviews:

Related manuals for N5221B

Brands by name

Popular brands

Keysight Technologies N5221B, Manual

Search results

Summary of Contents for N5221B

Reviews:

Related manuals for N5221B

Brands by name

Popular brands