Keysight Technologies N4917CPCA User Manual Download Page 16 | Manualshive

Page: 16 / 84

background image

16

Keysight N4917CPCA Optical Receiver Stress Test for CPRI Fronthaul Networks User Guide

2

System Requirements for N4917CPCA

Attenuators:
• 81576A Attenuator module (straight SMF) or
• 81577A Attenuator module (angled SMF) or
• N7761A external Attenuator (1 ch straight SMF) or
• N7762A external Attenuator (2 ch straight SMF) or
• N7764A external Attenuator (4 ch straight SMF)
• N7766A external Attenuator (2 ch MMF)
• N7768A external Attenuator (4 ch MMF)

DCA-X Oscilloscope

• 86100D-ETR/PTB/200/300 DCA-X mainframe
• N1000A-PLK/LOJ/PTB DCA-X mainframe

• 86105D-281/IRC 50 GHz Electrical, 34 GHz Optical module or
• 86115D-282/IRC dual 34 GHz Optical module or
• 86105C-200/IRC 20 GHz Electrical, 9 GHz Optical module

• 86107A-020 Precision Time Base (not required, if DCA-X has the option

–PTB)

DCA-M Oscilloscope

• N1092A one optical channel or
• N1092B two optical channels or
• N1092C one optical, two electrical channels or
• N1092D four optical channels or
• N1092E two optical, two electrical channels
• options LOJ/PLK/IRC/200/300/500

Clock Recovery

• N1077A-216-SMS Clock Recovery 50 Mbd - 16 Gbd
• N1077A-232-SMS Clock Recovery 50 Mbd - 32 Gbd
• N1078A-216-S50 Clock Recovery 125 Mbd - 16 Gbd

«
...
14
15
16
17
18
...
»

Summary of Contents for N4917CPCA





















































































Reviews:

No comments

Related manuals for N4917CPCA

Brand: Campden instruments Pages: 8

Brand: iGuzzini Pages: 20

Brand: Bahco Pages: 9

Brand: GALBIATI Pages: 20

Brand: Datex-Ohmeda Pages: 80

Brand: MacDon Pages: 2

Brand: V-TAC Pages: 6

Brand: Kanlux Pages: 4

IQ Express RF6118

Brand: Mainpine Pages: 2

IMPULSE 2 IT8026 Glute Master

Brand: BM FITNESS Pages: 18

Brand: My-Doc Pages: 32

Brand: Spitzer LIGHTING Pages: 2

Brand: Cameo Pages: 56

Brand: Eleiko Pages: 24

Brand: Horizon Fitness Pages: 17

Brand: Wiltron Pages: 13

Brand: Cutler-Hammer Pages: 45

Brand: NSF Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands