background image

Safety instructions

 

 

Do not make any changes to the engine's upper idle speed. Too high a speed increases the risk of
accidents.

Unauthorized conversions that endanger the operational safety of the machine are prohibited!

Check the machine for operational safety before each use!

3.2.2  Work and danger area 

The user is responsible to third parties in the work area!

Staying in the danger area of the machine is prohibited!

Check the near range before starting up. Pay special attention to children and animals. Ensure
sufficient visibility!

Before starting work, remove foreign objects from the surface to be worked. Pay attention to
other foreign objects during work and eliminate them in good time.

When working in enclosed areas, the safety distance to the border must be maintained so as not
to damage the tool.

When working in the immediate vicinity of public roads and paths, these should not be
approached if possible, because there is a risk of injury to third parties due to flying objects.

When working on public roads and squares or in the immediate vicinity, warning and danger
signs should be set up in order to attract the attention of third parties.

3.2.3  Before starting work 

Before starting work, please familiarize yourself with all the devices and actuators as well as their
function and make sure that all safety devices are properly installed and in the protective position! It's
too late during the work assignment!

Above all, learn how to stop the engine quickly and safely in an emergency.

3.2.4  Starting the machine 

When starting the engine, all drives must be switched off!

Do not run the engine indoors!

Do not step in front of the single-axle tractor or the implement to start the engine.

Do not use jumper fluids when using electric jump start (jumper cable). There is a danger of
explosion!

3.2.5  During operation 

Never adjust the operating handle while driving - risk of accident!

The transport of persons and objects is prohibited!

If, for example, the attachment has caught a foreign object and blocked it, stop the engine and clean
the attachment with a suitable tool! Always switch off the engine when handling or cleaning the
implement!

Do not leave the operating station until all tools of the attachment have come to a standstill!

In the event of damage to the self-propelled implement or attachment, stop the engine immediately
and have the damage repaired.

If the steering fails, stop the self-propelled implement immediately and stop the engine. Have the
fault rectified immediately.

Summary of Contents for K2100


























Reviews: