background image

About this manual 

About this manual 

The machine or implement is subject to technical progress. All information, illustrations and 
technical data are up-to-date at the time of publication. Changes in the sense of technical progress 
are reserved to the manufacturer at any time. 

Therefore, no claims can be derived from the information and illustrations in this booklet. 

2.1  Before commissioning 

As self-propelled implements and implements can cause serious accidents or hazards if used 
improperly, a briefing of competent and authorized persons is mandatory when commissioning 
the Kersten implement for the first time. 
The best way to familiarize yourself with its basic functions and its handling is to choose a free 
and level terrain for your first trip. 

You reduce the risk of accidents on your part or third parties!

For further information and difficulties of any kind, please contact the dealer, importer or directly 
to the manufacturer. 

Be sure to read the safety instructions on the following pages!

Read the operating instructions before commissioning!

Pass on all safety instructions to other users!

2.2  Notes on this operating manual 

Enumerations are marked with eye-catching points.

Example:

Text

Text

Instructions are marked according to the order in which they are to be executed.

Example:

1. Text
2. Text

Summary of Contents for K2100


























Reviews: