Kemper KHS Logic Control System, Installation And Operating Instructions Manual

Page: 76 / 112

- 0 -
Installation and Operating Instructions
KEMPER KHS Logic Control System
Figure 686 02 003, Individual Design
Firmware version: V-3.2.6
Content
1. Hardware installation …………………………………………………………………………...................................... .. P.1
1.1 System requirements for laptop / PC of the customer ……………………………………………………. P.1
1.2 Scope of application / Special safety instructions ………………………………………………... . ………. P.1
1.3 Setup ………………………………………………………………………………………………………………. P.1
1.4 Structural layout……………………………………………………………................................................... P.2
1.4.1 Explanation of buttons, control box exterior……………………………............................... P.2
1.5 Hardware equipment…………………………………………………………………………………………… P.3
1.6 Circuit diagram…………………………………………………………………………………………. ………. P.3
1.6.1 Connection example, servo drive Type A……………………………………………………… ... P.4
1.6.2 Connection example, flow measurement valve……………………………………………….. P.5
1.6.3 Connection example, hygienic flushing………………………………………………………… P.6
1.6.4 Connection example, cold water temperature measurement valve (PT1000) ………… ... P.7
1.6.5 Connection example, hot water temperature measurement valve (PT1000) ……………. P.8
1.6.6 Connection example for external release……………………………………………........... .... P.9
1.6.7 Connection example of the "Fault" contact and the "Ready to Operate" contacts ……. P.10
2. Setting up the network connection….……………………………………………………..............................………. P.11
3. Webserver…………...……………………………………………………………………………………………… . ………. P.15
3.1 Reference object, "Flushing".…………………………………………………………................................. P.15
3.1.1 Adding a user…….…..……………………………………………………………….................... . P.16
3.1.2 Setting/changing the IP address…………………………………………………………………. P.16
3. 1.3 Adding components…….…..……………………………………………………………………… P.17
3.1.4 Configuring A- valves..............................................................................……………………… P.17
3.1.5 Configuring B-valves................................................. .............................……………..……….. P.18
3.1.6 Configuring C- valves..............................................................................……………………… P.18
3.1.7 Configuring flow rate sensors................................................... ...........................…………… P.19
3.1.8 Configuring temperature sensors.......................................................................................... P.20
3.1.9 Configuring the hygienic flushing ………………………………………………………………. P.20
3.1.10 Ove rview of the valves and sensors.……….…….................................................... ……….. P.21
3.1.11 Manual operation of A-/B- or C- valves and hygienic flushings (individually)…............... P.22
3.1.12 Manual operation of A-valves and B-valv es via a group…………………..……………… .. P.22
3.1.13 Volume control through individual A-valve / C- valve.……….……………………………… P.23
3.1.14 Time control through individual A-valve / C- valve.……….………………………............... . P.23
3.1.14 Temperature control through individual A-valve / C- valve.……….……………………….. P.24
3.1.16 Flushing log……………………..…………………………………………………………………. P.25
3.1.17 Current fault messages……….………………………………………………………………….. P.25
3.1.18 Fault message / error log.……………………………………………………………................. P.26
3.2 Temperature monitoring………………………………………………………………….............................. P.26
3.2.1 Adding drinking water temperature sensors….…..………………......….............................. P.27
3.2.2 Configuring drinking water temperature sensors….…..………………......…...................... P.27
3.2.3 Configuration of the recording / monitoring………………………………………................. P.28
3.2.4 Temperature log……………………………………………………………………....................... P.29
3.2.5 Temperature overview………………….……………………………..…………………………… P.30
3.2.6 Temperature fault (exceeding or undercutting)………………………………………………. P.30
3.3 Backing up and restoring the configuration………………………………………………………………… P.31
4. Wiring for KEMPER KHS components with electrical connection ……………………….................. ............... P.33
5. Connections in laptop, network or BMS……………………………………………………………………….. ……….. P.34