background image

5

Table of contents >>

SURROUNDINGS

Make sure your working area is clear from people, children and objects before installing and 

using the machine. Risk of serious injuries can occur during operation. Take an extra caution 

when children are in the area where the equipment/ product is being use or stored. Check 

the area for low hanging electrical wires. Be careful when working on slopes and near ditches. 

Always work alone with single - purpose tools/products. Never have junk lying in your area. 

Keep working areas clean. Always respect the risk zone.

STEPS BEFORE USE

Read the safety information and instruction manual carefully. Be sure you understand the safety meas-

ures, instruction manual and warning labels. Use common sense when operating the machine and use 

appropriate personal protective equipment.

Always check the performance and the machine combination that are used. It’s highly important these 

matches in a satisfactory manner. This is to ensure the product or the function and most important yours 

and others safety. Do visual inspection of equipment or product before use. Fix or replace damaged or 

worn parts immediately to reduce the risk of injury. Lubricate moving parts and check that all screw-nuts 

and bolts are tightened.

Learn and remember the correct working methods. Beginners should always keep a low speed, use ex-

treme caution before routine and product knowledge is achieved. The user/customer is responsible to 

handle the situation correctly. The product should not be taken into use unless it can be done in a safe 

way for the user.

Read the tractor’s manual before connecting equipment.
• 

Check and tighten all nuts and bolts!

• 

Check the oil level in the gear box, fill as necessary.

• 

Check V-belt tension and adjust if necessary.

• 

Check that the flails are not defective, replace if necessary.

• 

IMPORTANT! Always check lubrication oil level in the shaft before performing any operation!

The user / customer is responsible for handling the situation. If you experience that the ma-
chine is not safe to use, the machine must not be used until it is properly checked and insured 
it is working properly.

DANGER!

Children in the area should be supervised.

ENVIRONMENT

 Disposal of oil and other waste

• 

Improper disposal of oil or other waste can damage the environ-

ment.

• 

When the machine is emptied of oil, it must be poured into a 

dense container special made for oil. It is not allowed to store oil 

in a container that is being used for food or drink, to avoid the oil 

being consumed by mistake by others and cause serious injuries.

• 

It is forbidden to spill the oil on the ground or empty it into 

drains or somewhere that leads to a water source.

• 

Discarded oil, fuel, coolant, brake fluid, filter or battery must not 

be thrown or dispossed just anywhere. Contact your municipal-

ity for further information.

Summary of Contents for 35-SKL145

























Reviews: