background image

10

Table of contents >>

RISKS AND HAZARDS DURING USE OF MOWING MACHINES

Risk of crushing

Bystanders may be injured when the machine is lowered to the cutting position. The machine 

has crushing points around the hinge areas and between the three-point hitch mount and the 

main body.

Rotating blades

All persons will be at risk of injury if they stick out their hands or feet under the machine when 

it is lifted from the ground and the blades are rotating.

Risk of pinching or risk of trapping body parts

This risk is common in transmission devices such as belt drives, gears and rollers. Ensure that 

all guards are fitted correctly.

Warning! Rotating knives

Risk during disengaging of the machine

The heavier the rotating part is, the longer it will continue to rotate after the drive has been 

switched off. This feature is called ”free-wheeling” . Rotating blades and other components, 

such as drive shafts, etc. will continue to spin after the drive has been disconnected. Injuries 

may occur:

• 

When the operator releases the equipment, and try to clean or adjust the machine 

before the components have stopped rotating.

• 

When the shear bolt in the protective device in the power take off breaks and rotors 

still spinning while the PTO has stopped. Operator’s awareness is the key to safety 

around rotating parts. Do not raise the machine while the blades are rotating.

Risk of ejecting objects

Machines that mows throws out material while driving. Foreign objects such as rocks, sticks 

and other debris can get into the machine and ejected with tremendous speed. Covers on the 

sides and the front prevents these objects to be thrown out but it does not always guarantee 

that the guards catch everything  that is thrown out.

Bystanders or animals that standing on the way of the projected object can be 

seriously injured. Never allow bystanders within the vicinity of the machine. Re-

spect the machine’s danger zone. 

Danger

 

zone 25m!

Noise

Please note that the machine is normally used outdoors and that the position of the operator 

is in the driving seat of the tractor. It is advisable to read the regulations specified in the tractor 

manual and maintenance instructions.

The sound pressure level exceeds 70 dB during operation. Hearing protection should be used 

while driving.

Summary of Contents for 35-SKL145

























Reviews: