background image

3  Technical Data

Unless otherwise indicated, all electrical data in the following chapter refer to a 3-phase 

AC voltage supply.

3.1  Operating conditions

3.1.1  climatic ambient conditions

Storage

Standard

class

Notes

Surrounding temperature

EN 60721-3-1

1K4

-25…55 °C

Relative humidity

EN 60721-3-1

1K3

5…95 %  (without condensation)

Storage height

Max. 3000 m above sea level

Transport

Standard

class

Notes

Surrounding temperature

EN 60721-3-2

2K3

-25…70 °C

Relative humidity

EN 60721-3-2

2K3

95 % at 40 °C (without condensation)

Operation

Standard

class

Notes

Surrounding temperature

EN 60721-3-3

3K3

5…40 °C (extended to -10…45 °C)

Coolant inlet  

temperature

Air

5…40 °C (-10…45 °C)

Liquid

5…40 °C

Relative humidity

EN 60721-3-3

3K3

5…85 %  (without condensation)

Version and degree of  

protection

EN 60529

IP20

Protection against foreign material > ø12.5 mm 
No protection against water
Non-conductive pollution, occasional conden-

sation when PDS is out of service.

Site altitude

Max. 2000 m above sea level
•  With site altitudes over 1000 m a derating 

of 1 % per 100 m must be taken into con-

sideration.

•  With site altitudes over 2000 m, the control 

board to the mains has only basic isola-

tion. Additional measures must be carried 

out when wiring the control system.

Table 2: 

Climatic ambient conditions

25

 OPerATING  cONDITIONS

Summary of Contents for COMBIVERT G6 series





















































Reviews: