KBL megaSun 5600 Manual Download Page 55

Page: 55 / 63

This error message is displayed on the operating panel and
can be acknowledged by pressing the “Stop“ key. Prior to this,
service staff has to nd the reasons of these error messages.
Possible reasons can be:

• temperature in the unit is too high
• exhaust vent system is defectiv

This message will be displayed after 40 minutes of uninterrupted
operation of the tanning system.
By turning off the coin-operated system this message is
acknowledged.

E01BUS:ABL

There is not any data link between the controller board and the
revolution control...
Reason: defective or not connected I²C revolution control.

E02:BUS:TMP

Reason: defective or not connected I²C temperature sensor.
Solution: press the START key. The blower is running with max.
revolution during the temperature controll.

BUS-Error

Daten line of the Bus I²C-Bus is disturbed

— 230 V is missing at MP3-Player or Audio Switch
— Bus connector at MP3-Player in wrong position

E04:BUS:VOIC

Reason: There is not any data link between the controller board
and the MP3 player Voice.
Solution: press the START key. The controller is working as one
w/o megaVoice.
Reason:

— missing soldering bridge on MP3-Player megaVoice,
— SD card not readable
— formating or wrong inserted,
— Plug at MP3 iInterface or at I²C Audio switch is

inserted uncorrect.

E05BUS:REL

Conguration error: I²C-Relay board (8) an I²C Relais board (2) at
the same time connected.

Summary of Contents for megaSun 5600
































































Search results

Summary of Contents for megaSun 5600

Reviews:

Related manuals for megaSun 5600

Brands by name

Popular brands

KBL megaSun 5600, Manual

Search results

Summary of Contents for megaSun 5600

Reviews:

Related manuals for megaSun 5600

Brands by name

Popular brands