Kaysun KEM-30 DNS3 Owners & Installation Manual Download Page 7

Page: 7 / 60

3. BEFORE INSTALLATION

Handling of the unit

The angle of inclination should be between 45º and 70º when carrying the unit in case the machine turns over.

a. Rolling handling: several rolling rods of the same size are placed under the base of the unit, and the length of each rod must be

more than the outer frame of the base and suitable for balancing of the unit.

b. Lifting: each lifting rope (belt) should be able to bear 4 times the weight of the unit. Check the lifting hook and ensure that it is firmly

attached to the unit. To avoid damages to the unit, a protective block made of wood, cloth or hard paper should be placed between

the unit and rope when lifting, and its thickness should be 50mm or more. It is strictly forbidden to stand under the machine when it

is hoisted.

Lifted cable

4 protective blocks should be placed.

Unilateral distance should be 50mm or more.

The angle of inclination (45~70°)

Lifted hook

The angle of inclination (45~70°)

Fig. 3-1 Lifting of the unit

Summary of Contents for KEM-30 DNS3





























































Search results

Summary of Contents for KEM-30 DNS3

Reviews:

Related manuals for KEM-30 DNS3

Brands by name

Popular brands

Kaysun KEM-30 DNS3, Owners & Installation Manual

Search results

Summary of Contents for KEM-30 DNS3

Reviews:

Related manuals for KEM-30 DNS3

Brands by name

Popular brands