Kaysun KEM-30 DNS3 Owners & Installation Manual Download Page 23

Page: 23 / 60

No.

Detail information

CN2: HEAT1. Pipeline Auxiliary Heater

Attention: the control port value of the pump actually detected is ON/OFF but not 220-230V control power supply,

special attention should be paid when installing the pipeline auxiliary heater.

CN85:

The alarm signal output of the unit(ON/OFF signal)

Attention: the control port value of the pump actually detected is ON/OFF but not 220-230V control power supply,

special attention should be paid when installing the alarm signal output.

Discharge temperature switch protection (protection code P0, provent the compressor from over temperature 115°C)

CN71: System electronic expansion valve2. Used for cooling.

CN72: EVI electronic expansion valve. Used for EVI.

CN70: System electronic expansion valve1. Used for heating.

CN60: Outdoor units communication or HMI communication port

CN61: Outdoor units communication or HMI communication port

CN64: Fan inverter module communication ports

CN65: Compressor inverter module communication ports

CN300: Program burn in port (WizPro200RS programming device).

IC10: EEPROM chip

CN1: temperature sensors input port.

T4: outdoor ambient temperature sensor

T3A/T3B: pipe temperature sensor of the condenser

T5: water tank temperature sensor

T6A: Refrigerant inlet temperature of EVI plate heat exchanger

T6B: Refrigerant inlet temperature of EVI plate heat exchanger

CN16: System pressure sensor

CN31: Temperature sensors input port

Th: System suction temperature sensor

Taf2: Water side antifreeze temperature sensor

Two: Unit water outlet temperature sensor

Twi: Unit water inlet temperature sensor

Tw: Total water outlet temperature sensor when several units are connected in parallel

CN3: Module 1 temperature sensor

CN10: Module 2 temperature sensor

CN15: Detection of current of the compressor system input port

INV1

Detection of current of the compressor A

INV2

Detection of current of the compressor B

Summary of Contents for KEM-30 DNS3





























































Search results

Summary of Contents for KEM-30 DNS3

Reviews:

Related manuals for KEM-30 DNS3

Brands by name

Popular brands

Kaysun KEM-30 DNS3, Owners & Installation Manual

Search results

Summary of Contents for KEM-30 DNS3

Reviews:

Related manuals for KEM-30 DNS3

Brands by name

Popular brands