KaVo KEY Laser 3+ 1343 Instructions For Use Manual Download Page 34

Page: 34 / 80

CAUTION

Dropping the laser hose.

Damage to the coating and construction of the exit window.

▶ Do not let the laser hose drop.

▶ Do not bump the laser hose couplings or set them down roughly.

▶ Make sure that the exit window of the laser coupling is not dirty or does not

have fingerprints.

See also: Section 2.3 of the handpiece instructions

▶ Insert the laser hose coupling ② in the input block, and make sure that the plugs

are correctly aligned.

▶ Screw tight with the union nut.

▶ Guide the laser hose through the swing arm ① .

4.3.2

Couple the handpieces

Note
Make sure that the KEY Laser 3+ / III upgraded is switched to stand by.

▶ Remove caps ① and ② .

Instructions for use KEY Laser 3+ 1343 KEY Laser III 1243 upgraded
4 Operation | 4.3 Laser hose and handpieces

32/76

Summary of Contents for KEY Laser 3+ 1343

















































































Search results

Summary of Contents for KEY Laser 3+ 1343

Reviews:

Related manuals for KEY Laser 3+ 1343

Brands by name

Popular brands

KaVo KEY Laser 3+ 1343, Instructions For Use Manual

Search results

Summary of Contents for KEY Laser 3+ 1343

Reviews:

Related manuals for KEY Laser 3+ 1343

Brands by name

Popular brands