KaVo KEY Laser 3+ 1343 Instructions For Use Manual Download

Page: 30 / 80

Operating conditions

Ambient temperature

15 - 35 °C

Relative humidity

max. 85 %

Condensate on unit

not permissible

Suitable for operation up to 2,000 m above sea level.

Mode: Discontinuous operation

(valid only for load on the hand-piece. For the hand-piece mode, see hand-piece

instructions)

For a 1 min. pulse/1 min. pause with a unit setting of 600 mJ/13 Hz.

at an ambient temperature of 35 °C

permissible length of operation: 5 min.

at an ambient temperature of 25 °C

permissible length of operation: 30 min.

Therapy laser

Wavelength

2.94 µm (infrared)

Pulse energy

at the exit of the laser contra-angle hand

piece 2060 Mat. no. 1.000.4841)

80 - 600 mJ

Settable within a range of 80 - 200 mJ in 20 mJ steps
Settable within a range of 200 - 600 mJ in 50 mJ steps

Pulse frequency

2 - 30 Hz

Pulse duration

200 - 700 µs

Divergence

Divergence of the laser beam after exit‐

ing the laser contra-angle hand-piece

2060 (Mat. no. 1.000.4841)

approximately 5 - 10 °

NOHD

1 m

Pilot laser

Laser type

Red laser diode

Laser class

2 / max 1 mW

Wavelength

655 nm red

Instructions for use KEY Laser 3+ 1343 KEY Laser III 1243 upgraded
3 Device description | 3.5 Technical data and requirements

28/76

Summary of Contents for KEY Laser 3+ 1343

















































































Search results

Summary of Contents for KEY Laser 3+ 1343

Reviews:

Related manuals for KEY Laser 3+ 1343

Brands by name

Popular brands

KaVo KEY Laser 3+ 1343, Instructions For Use Manual

Search results

Summary of Contents for KEY Laser 3+ 1343

Reviews:

Related manuals for KEY Laser 3+ 1343

Brands by name

Popular brands